Support

An unlabeled alternator switch, left off, stopped the engine of a Zenith CH 750 in flight, the NTSB found

An NTSB report on a Zenith CH 750 with a Viking 110 engine found both batteries discharged after a forced landing. The engine's ignition needed battery power, the switch that turned on the alternator had no label, the panel had no alternator warning light, and the pilot used no checklist. Labels, one checklist line and a low-voltage warning each cost little.

18 Nov 2026

A builder knows every switch on the panel, because the builder put them there. That's the reason labels get left for later, and on some airplanes later never comes. An NTSB report on a Zenith CH 750 shows what an unlabeled switch can cost when the engine behind it runs on electricity.

The airplane, N752VK, was an amateur-built CH 750 finished in 2012, with a Viking 110 engine and 701 hours on the airframe. On September 23, 2018, its owner, a private pilot with 237 hours, took off from DeLand Municipal Airport in Florida with a passenger at about 3:30 in the afternoon. About 15 minutes later, near DeLeon Springs, the engine started "skipping," then quit, and the propeller stopped. The pilot steered clear of power lines on the way down. The airplane touched down steeply in an open area, nosed over and came to rest inverted. Both people had minor injuries. The NTSB's final report, ERA18TA263, was published November 19, 2019.

A Zenith STOL CH 750, N750SZ, parked at the Viking engines display at Sun 'n Fun, Lakeland, Florida, on April 10, 2024, its cabin under a cover and "VIKING POWER" lettered on its side. The FAA registry lists N750SZ as a 2013 amateur-built STOL CH 750 with a Viking 110 engine, the same engine as the accident airplane. It is not the accident airplane. Photo: ZLEA, CC BY-SA 4.0, via Wikimedia Commons.
A Zenith STOL CH 750, N750SZ, parked at the Viking engines display at Sun 'n Fun, Lakeland, Florida, on April 10, 2024, its cabin under a cover and "VIKING POWER" lettered on its side. The FAA registry lists N750SZ as a 2013 amateur-built STOL CH 750 with a Viking 110 engine, the same engine as the accident airplane. It is not the accident airplane. Photo: ZLEA, CC BY-SA 4.0, via Wikimedia Commons.

What the inspector found

Nothing was wrong with the engine. An FAA inspector found two 12-volt motorcycle batteries aboard, both discharged: one read 0.75 volts and the other 7 volts. He and a mechanic charged them, and the engine started and ran normally. The alternator charged normally too, with the bus above 13.5 volts.

The Viking 110 has an electronic control unit in place of magnetos. The report notes that the engine manual reminds operators of what follows from that: at least one battery has to keep its charge for the engine to run.

The alternator was turned on by a key-operated rotary switch on the panel, the same switch that started the engine. It had no label. In one position the alternator's field wire had power and the alternator charged. In the other the field had no power, and the engine went on running from whichever battery was switched on, for as long as that battery lasted. The two battery toggle switches had no labels either.

The pilot told the inspector he may have left the alternator switch off by mistake. He also said he did not use a checklist. And there was nothing on the panel to tell him: the report says the engine manual recommended an alternator warning light, and none was installed.

The NTSB's probable cause is "the pilot's operation of the airplane with the alternator switch in the off position, which allowed the selected battery to discharge and resulted in an ignition system failure and a total loss of engine power." Its findings list the pilot's forgotten action and the checklist, and one against the airplane: the design of its DC indicating system.

Three cheap fixes

The report names three things that were missing. None of them is expensive.

Labels. Every switch gets its name, and its on and off positions where they are not obvious. A key switch that also controls the alternator needs each position marked, because nobody expects that of a key switch. The test is whether a pilot who has never sat in the airplane could set it up for flight from what the panel says. A label maker's tape does the job on a flying airplane. Engraved or printed placards do it for good, and they are easiest to plan while the panel is still a drawing. Hangar Flying's Panel Designer has templates for the STOL CH 750 and the CH 750 Cruzer, and a layout drawn there shows where the switch row and its lettering will fit before any metal is cut.

A checklist line. "Alternator on, voltage checked" after engine start and again before takeoff would have caught this one. The check needs a number to look for. A bus fed by a working alternator reads well above battery voltage; this airplane's read more than 13.5 volts once the switch was on. A reading that stays down at battery voltage with the engine running means the battery is carrying the airplane alone.

A low-voltage warning. A voltmeter only helps a pilot who looks at it. A warning light, or an alarm from an engine monitor, does not wait to be looked at. Viking's installation page today says of its engines, "we use digital voltmeter @ 14.4 V to indicate alternator failure." For an airplane with an externally regulated alternator, B&C Specialty Products' LR3E-14 alternator controller ($325, sold for amateur-built aircraft only) includes a panel warning light that, by B&C's data sheet, "illuminates whenever bus voltage drops below 12.7V." A builder with an engine monitor or an electronic flight display can look in its installation manual for a voltage alarm, set it, and confirm on the ground that it works the way the manual describes.

Why it matters more with electronic ignition

A magneto makes its own spark. With magnetos, a dead alternator costs the radios and the lights, and the engine keeps running. An engine with an electronic control unit, electronic ignition or electric fuel pumps and no engine-driven backup stops when the battery does. On this airplane that took about 15 minutes, though the report does not say how much charge the battery had at takeoff.

So on an electrically dependent engine the alternator switch, the battery switches and the voltage warning are engine controls, and they deserve the same care in labeling and in the checklist as the fuel selector. The engine maker's installation manual is the place to start: it says what the engine needs from the electrical system and what warning the maker expects to see on the panel.

Sources

For information only. Not approved data. Follow the manufacturer's instructions and the regulations.

Source: data.ntsb.gov

All articles